Structures
Wing box load paths: from air load to internal load
From air pressure on the skin to the fuselage frames, one free body at a time.
Mostly AI-generated, checked by a practising aircraft stress engineer Last updated
Not guaranteed to be correct. For learning only, not for real engineering work: how the content is made.
Contents
1How to read the drawings#
Every drawing uses the same arrow colours, so a colour always means the same kind of load.
- Views. Cross-sections have the leading edge on the left and the upper surface up. Spanwise views have the fuselage on the left and the tip on the right.
- Free bodies. A cut through the wing always shows the outboard part. Arrows on the cut face are what the inboard structure does to it.
- Load case. Positive flight (+2.5 g, lift up) unless a drawing says otherwise.
- Numbers. All loads come from one illustrative teaching wing sized like a 737-800. They are not Boeing data.
| Symbol | Meaning | Unit |
|---|---|---|
| Lift | kN | |
| Offset of the centre of pressure from the shear centre | m | |
| Torque | kN·m | |
| Load factor, written as a multiple of g in the text (+2.5 g) | none | |
| Weight | kN | |
| Pressure on the skin | kPa | |
| A force: the load on one skin panel, and the frame loads and at the STA 540 and STA 663.75 frames | N, kN | |
| Running load on a stringer | N/m | |
| Stringer pitch | m | |
| Rib pitch, the length of one bay between two ribs. The same length is called in Figure 9.1 and in Section 11 | m | |
| Rib number along the span, in Figure 6.1 | none | |
| Reaction at a support: from a rib on a stringer, or from a spar on a rib (, ). In Section 11 the same letter is the radius of the bend. R1 to R8 are fitting names, not reactions | N, kN; m for the radius | |
| Shear force. is the rib load added in one bay | kN | |
| Bending moment | kN·m | |
| Depth of the box between the covers | m | |
| Load in one cover, compression in the upper cover and tension in the lower. is the load added in one bay | kN, MN | |
| Shear flow, the force per unit length along a wall | N/mm | |
| Rib pitch, in Section 11 (the same length as ) | mm | |
| Running load in a cover, in Figure 11.3 | N/mm | |
| Area enclosed by the four box walls | m² |
2The whole chain at a glance#
Pressure enters at the skin and leaves at the fuselage frames. Each element is loaded by the one before it and held by the one after it. The numbers are the eight steps of this article: seven hand-overs along the chain, and torsion, which the spar webs and the covers carry together. The step labels on the sections below use the same numbers.
3The structure: 737 NG wing box#
The wing box is a closed tube: two spars, an upper cover and a lower cover, with ribs across it. In a box of this kind the spar webs carry the shear, and the skins and stringers share the bending with the spar chords [7].
The 737 NG is the example throughout because its structure is widely described in public sources.
Seen from above, ribs run from front spar to rear spar and stringers run from root to tip. The box is also a fuel tank: on the 737 NG the main tank lies inside it, bounded by the front and rear spars [4][1].
| Part | 737 NG fact | Job in the load path |
|---|---|---|
| Skin panels | Probably 7055 alloy (upper) and 2324 (lower), though no public source confirmed this for the 737 NG; both are standard for these skins on commercial jets [8] | Take the air pressure; carry bending as compression (upper) and tension (lower) |
| Stringers | Section shape not public; wing stringers can be J, Z or hat sections, among other shapes [8]. Named by letter and number, such as U-14 on the 737-800 wing [5] | Beams between ribs; share the bending load with the skin |
| Ribs | Rib count is not public (see the caveat below). Ribs are numbered, such as rib 21 at WSTA 617 on the 737-800 wing [5] | Collect stringer loads, hand them to the spars, hold the box shape |
| Spars | Two spars [1] | Webs carry vertical shear to the root |
| Side-of-body rib | At WBL 71.24 on the 737-800 [1] | Joins the outer wing to the centre wing box |
| Centre wing box | Front spar at the STA 540 frame [2], rear spar at STA 663.75 [3] | Balances left wing against right; passes net lift to the fuselage |
4The external load#
Air load arrives as pressure on the skin, and the structure sees the lift minus the weights the wing carries itself.
In cruise nearly all of the lift is suction on the upper skin, so the lift is pulled up through the upper skin. The lower skin carries a weaker, mixed air load: pushed inward near the nose and near the trailing edge, and pulled outward under the wing box in between. Push and pull here mean outside pressure above or below the surrounding atmosphere. The resultant acts at the centre of pressure. Its offset from the shear centre twists the box with torque . Flaps move the centre of pressure aft and add nose-down torque.
Published pressure plots all use this layout. The vertical axis is upside down, so suction is at the top. The higher curve is the upper skin. The lower skin is pulled outward wherever its curve is above the zero line. The wing box sits between about 15% and 65% of the chord.
At +2.5 g the wing flies at a higher angle of attack. Upper-skin suction roughly doubles, and the lower skin is pushed inward over the front of the chord instead of being pulled out. The load numbers in the rest of this article are for this case.
Every mass in the wing pushes down with and offsets lift. This is inertia relief. It is why engines hang on the wing and why centre-tank fuel is burned before wing fuel.
| Item | Load | Distance from side of body |
|---|---|---|
| Lift on one wing | 691 kN up | 6.3 m |
| Wing structure | 98 kN down | 6.0 m |
| Main tank fuel, 3,900 kg: one full wing tank of 4,875 litres [6] at about 0.8 kg per litre | 96 kN down | 4.5 m |
| Engine, nacelle, strut | 74 kN down | 3.1 m |
| Root shear | 423 kN | |
| Root bending moment | 3,100 kN·m |
Going inboard, shear drops by 74 kN at the engine because the engine weight comes off the lift there. Bending only kinks, since its slope equals the shear. Torque steps wherever a load sits off the box: engine, flap tracks, aileron hinges. On the ground the signs flip outboard of the main gear, because the wing then hangs from the gear.
Step 1
5Air pressure loads a skin panel#
A skin panel is a thin plate held along its edges by two stringers and two ribs, and pressure bends it between them.
- Upper skin (suction): the skin is pulled away from the stringers, so the fasteners are in tension.
- Lower skin: in cruise the air load is small and changes sign along the chord. Where the outside pressure is higher, the skin bears on the stringer flanges. Where it is lower, the fasteners pull, as on the upper skin.
- Fuel sits on the lower skin and presses it outward. In cruise this can outweigh the air load on a lower panel.
In 1 g cruise the lower panel sees two loads in the same direction: mild suction outside, roughly 2 to 4 kPa as an estimate, and fuel weight inside. Both pull the skin away from the stringers, so the fasteners work in tension here too. Upper-skin suction in cruise is nearer 9 kPa than the 20 kPa of the worked example.
Steps 2 and 3
6Skin to stringers, stringers to ribs#
Each stringer collects half a panel from either side, so it carries a running load and spans between ribs like a beam.
- Running load: .
- Reaction at each rib from one bay: . With the bay on the other side, each rib takes 1,800 N per stringer.
- On the upper cover the stringer is also in compression from wing bending. Pressure bends it while compression squeezes it, so it works as a beam-column. The ribs keep its buckling length short.
Step 3 close-up
7Where the stringer crosses the rib#
The stringer runs through a cut-out in the rib, and a clip bolted to both passes the reaction into the rib web [10].
Shear ties between the cut-outs also fasten the skin straight to the rib, so a small share of the pressure skips the stringer.
Step 4
8Ribs deliver the air load to the spars#
A rib is a short, deep beam spanning chordwise between the two spars. Stringer reactions and shear-tie loads push it up, and the spar webs hold it down at each end.
Ribs also resist a crushing load that comes from wing bending. It depends on the cover loads of Step 5, so it is explained right after that step.
Step 5
9Spar webs carry shear, covers carry bending#
Each rib adds its load to the spars, so spar shear grows rib by rib toward the root. The growing bending moment is carried as a push in the upper cover and a pull in the lower cover.
- Covers. . At the root: , about 3.9 MN in each cover. Spread over a 2.8 m wide cover with 7 mm smeared thickness, that is about 198 MPa.
- Webs. Shear flow . With two equal webs: in each.
- Why two alloys. In flight the upper cover is in compression and the lower cover in tension, so the wings of commercial jets have for the most part used a 7000-series alloy on top, such as 7050 or 7055, and a 2000-series alloy underneath, such as 2324, where fatigue life and fracture toughness matter as well as strength [8]. No public source confirmed which alloys the 737 NG uses.
- Other load cases. At negative g or on the ground the wing bends the other way and the cover signs swap.
Step 5 in depth
10How the upper skin ends up compressed#
1. Pressure only pushes through the skin. Steps 1 to 4 took the pressure through the stringers and ribs into the spar webs as vertical shear. Up to here nothing has loaded the skin along its length.
2. A web bay in shear tries to rotate. The tip side pushes the bay up and the root side holds it down. That pair of forces would spin the bay. The only things that can stop it are the covers, through the fastener rows along the top and bottom edges of the web.
3. The web pushes back on the covers. The upper cover holds the top edge of the web back, so the web pushes the upper cover toward the root. The lower cover holds the bottom edge the other way, so the web pulls the lower cover toward the tip. This edge load is the shear flow , and it is the same on all four edges of the web bay.
4. The pushes pile up. Each bay adds to the cover. Nothing takes it out on the way, so the cover load at any station is the sum of everything added outboard of it. That sum is exactly .
At the root of the teaching wing the two webs together feed into each cover, so the cover load grows by 528 kN for every metre of span. The same number, within rounding, comes from . The bar values assume a constant 0.8 m box depth and are illustrative.
5. The load spreads across the cover. The webs meet the cover only along the two spar lines. From there the skin, working in shear in its own plane, carries the load sideways to each stringer. This is why the skin is fastened to every stringer, and why skin, stringers and spar chords all share the compression.
So the full chain for the upper skin is: pressure, stringers, ribs, web shear, shear flow along the web edge, cover compression. The lower skin gets the mirror image and ends up in tension. The beam picture and this picture are the same thing, since the shear flow along the web edges is what shortens the top of a beam and stretches the bottom.
11Back to the ribs: where the crushing load comes from#
The rib is squeezed because the covers are curved when the wing bends. Each cover carries a very large end-to-end force, and a force that has to follow a bend presses sideways on whatever holds it on the bend. The ribs hold the covers on the bend, so the ribs get pressed from both sides.
1. Where the force starts. From Step 5: at +2.5 g the upper cover carries about 3.9 MN of compression at the root, and the lower cover about 3.9 MN of tension. These forces run spanwise through the skin and stringers. They are the source of the crushing load. The air pressure is not: its net effect is to push the rib up, which is the load in Figure 8.1.
2. In a straight wing nothing happens. Look at one short piece of upper cover sitting on a rib. The cover on the root side pushes it one way and the cover on the tip side pushes it the other way. If the wing is straight, the two pushes are equal and exactly in line, so they cancel.
3. In a bent wing the two pushes are no longer in line. Tip-up bending curves the cover, so it arrives at the rib sloping down and leaves sloping up. Each push now has a large part along the wing and a small part pointing down. The along-wing parts still cancel. The two small down parts point the same way, so they add up. That leftover force presses the cover piece down onto the rib.
4. The lower cover does the same in reverse. It is in tension, so its neighbours pull the piece instead of pushing it. On the same tip-up curve, each pull has a small part pointing up. The leftover pulls the lower cover up, toward the middle of the box. So the rib is pressed down at its top and pulled up at its bottom.
5. How big it is. The leftover is the cover force times the small angle of the bend at that rib. Ribs a distance apart on a bend of radius give an angle of . With 800 N/mm in the cover, and , each cover presses on the rib with 8 N/mm, about 14 kN over a 1.8 m rib. That is nearly as large as the 16.2 kN of air load on the same rib.
6. How it gets into the rib and through it. The cover is skin plus stringers. Each stringer passes its share of the leftover force to the rib through its clip, and the skin passes its share through the shear ties (Figure 7.1). So the load enters the rib all along its top edge, pointing down, and all along its bottom edge, pointing up. The rib web carries it straight across from one edge to the other in compression, like a short column. Vertical stiffeners keep the thin web from buckling.
The top and bottom loads are equal and opposite, so they cancel inside the rib. None of the crushing load travels to the spars.
7. What happens without ribs. The covers would move toward each other, the box would get shallower and the wing would lose bending strength. This is the Brazier effect. It grows fast: the cover force and the curvature both rise with the bending moment, so doubling the moment makes the crushing load four times larger.
The whole chain: the wing bends, the covers curve, the cover force changes direction at each rib, a leftover force points toward the middle of the box, clips and shear ties pass it to the rib, and the rib web is compressed.
Step 6
12Torsion flows round the closed box#
- Torque: , with .
- The applied torque is nose-down, so the reaction on the cut face is nose-up, which is clockwise in this view.
- Add the two cases wall by wall. Front web: down. Rear web: down.
- Check: , which is the 423 kN root shear within rounding, and .
Step 7
13The wing root, side-of-body rib and centre wing box#
The vertical balance closes: 2 × 423 kN from the wings plus 336 kN of fuselage lift gives 1,182 kN up, equal to the 1,182 kN of fuselage and payload inertia.
At the side of body the outer wing turns up at its dihedral angle, taken as 6° here (illustrative), while the centre box runs straight. A cover load turning a corner needs a sideways force, and the side-of-body rib supplies it: at each cover. The rib pushes up on the upper cover and pulls down on the lower one, so the rib itself is squeezed.
Step 8
14Into the fuselage frames#
The front spar meets the fuselage at the STA 540 frame [2] and the rear spar at STA 663.75 [3], each side through a “pickle fork” fitting [11][12]. Sharing 423 kN and 150 kN·m between frames 3.14 m apart:
- , so
- and
15Concentrated loads take short, dedicated paths#
Engine. On the 737-800 the strut is pinned to the wing through fuse-pin joints: R1 upper link, R2 diagonal brace, R3 and R4 aft upper spar fittings, R7 and R8 side links [1]. Engine inertia acts forward of and below the box, so it adds a step in spar shear and a nose-down step in torque. In this teaching model, thrust is taken mainly through the diagonal brace and side loads through the side links. Exact fitting positions are not public, so the drawing is schematic. The nacelle and strut also change the air load on the wing [13]: air speeds up in the gap under the wing, which adds suction on the lower skin next to the engine.
Main landing gear. The forward trunnion sits in an H-block on the rear spar with four fuse pins [1]. The aft trunnion sits in the gear beam, which runs from the rear spar to a hanger link on the fuselage [1]. At landing the tyre load splits between the two trunnions. Outboard of the gear the wing then bends tip-down, so the cover signs reverse.
Slats and flaps. Slat load is up and forward. It goes through the slat tracks into nose ribs and reaches the front spar as an upward force plus a nose-up couple. Flap load is up and aft. It goes through the flap carriages and track into the rear spar and lower cover as an upward force plus a nose-down couple.
16Caveats and further reading#
- Illustrative numbers. Every load, stress, reaction and pressure comes from the teaching wing. The real 737 NG figures (the frame stations and the spacing between them, the side-of-body rib station and the size of the main tank) are cited where they appear. The skin alloys are the one item that no public source confirmed. Real work uses the aircraft’s own approved structural manuals and the manufacturer’s data.
- Schematic geometry. Rib count, spar positions, stringer pitch and exact strut and gear fitting positions are not public, so the drawings show the arrangement, not the dimensions.
- Torque sign. Nose-down torque is a teaching choice. The real sign changes with flight condition.
- Sign of the rib chord loads. With loads pushing up between two supports holding down, the rib bows upward, so the top chord is in tension, not in compression. Figure 8.1 uses that.
Pressure plots to study, closest to the 737 NG first:
- Tinoco, “Transonic CFD Applications at Boeing”, 1989 [13]: Figures 5 and 12. A real 737-300 wing, with the nacelle on and off.
- Gatlin et al., AIAA 2008-6917, DLR-F6 wind-tunnel test [14]: Figures 7(b) and 8(b). Measured pressures on a 25° swept wing [15] with underwing engines at Mach 0.75.
- Vassberg et al., AIAA 2008-6919, NASA Common Research Model [9]: Figure 13, page 18. Computed cruise pressures on both skins at eight span stations.
- Harris, NASA TP-2969, NASA Supercritical Airfoils [16]: Figure 7, PDF pages 45 to 48. One 2D section at low and high lift.
Sources#
- [1]National Transportation Safety Board, Structures Group Chairman’s Factual Report, DCA19FA143 (public docket DCA19MA143), 2019
- [2]Federal Aviation Administration, Proposed Airworthiness Directive, The Boeing Company airplanes, Docket FAA-2020-0331, 2020
- [3]Federal Aviation Administration, Airworthiness Directive 2019-20-02, The Boeing Company airplanes, 2019
- [4]Federal Aviation Administration, Airworthiness Directive 2010-24-11, The Boeing Company Model 737-600, -700, -700C, -800 and -900 series airplanes, 2010
- [5]Federal Aviation Administration, Airworthiness Directive 2019-22-06, The Boeing Company airplanes, 2019
- [6]European Union Aviation Safety Agency, Type-Certificate Data Sheet IM.A.120, Boeing 737, Issue 30, 2026
- [7]Alderliesten, Introduction to Aerospace Structures and Materials, TU Delft Open, 2018
- [8]Aluminum Company of America, Aluminum alloy products suited for commercial jet aircraft wing members, US5865911A, 1999
- [9]Vassberg et al., Development of a Common Research Model for Applied CFD Validation Studies, AIAA 2008-6919, 2008
- [10]TU Delft, AE1102 Introduction to Aerospace Engineering, structures slides, 2011
- [11]Leeham News, Boeing’s 737 in another pickle, 2019
- [12]Boeing, Aircraft wing-to-fuselage joint with active suspension and method, US9399508B2, 2016
- [13]Tinoco, Transonic CFD Applications at Boeing, 1989
- [14]Gatlin et al., Experimental Investigation of the DLR-F6 Transport Configuration in the National Transonic Facility, AIAA 2008-6917, 2008
- [15]Vassberg et al., Comparison of NTF Experimental Data with CFD Predictions from the Third AIAA CFD Drag Prediction Workshop, AIAA 2008-6918, 2008
- [16]Harris, NASA Supercritical Airfoils: A Matrix of Family-Related Airfoils, NASA TP-2969, 1990